Showing posts with label Panasonic. Show all posts
Showing posts with label Panasonic. Show all posts

Saturday, November 12, 2011

Grounding Transformers - Electrical Design, Transformer Design, and Distribution Transformer Design

!: Grounding Transformers - Electrical Design, Transformer Design, and Distribution Transformer Design

Grounding is clearly one of the most important aspects of electrical design, but it steadfastly continues to be misinterpreted and misunderstood. Millions of dollars in liability and loss can be attributed to ground-fault arcing; thus, grounding-related issues should top the checklists of any electrical contractor.

Grounding Transformers:

Simply put, a grounding transformer is used to provide a ground path to either an ungrounded "Y" or a delta connected system. Grounding transformers are typically used to:

Provide a relatively low impedance path to ground, thereby maintaining the system neutral at or near ground potential Limit the magnitude of transient over voltages when re-striking ground faults occur Provide a source of ground fault current during line-to-ground faults Permit the connection of phase to neutral loads when desired

If a single line-to-ground fault occurs on an ungrounded or isolated system, no return path exists for the fault current, thus no current flows. The system will continue to operate but the other two un-faulted lines will rise in voltage by the square root of 3, resulting in overstressing of the transformer insulation and other associated components on the system by 173%. MOV lightning arresters are particularly susceptible to damage from heating by leakage across the blocks even if the voltage increase is not sufficient to flash over. A grounding transformer provides a ground path to prevent this.

Large multi-turbine wind farms provide an example of the use of grounding transformers for fault protection on ungrounded lines. In many wind farms the substation transformer provides the sole ground source for the distribution system. When a ground fault on a collector cable causes the substation circuit breaker for that cable to open, the wind turbine string becomes isolated from the ground source.

The turbines do not always detect this fault or the fact that the string is isolated and ungrounded; thus the generators continue to energize the collector cable, and the voltages between the un-faulted cables and the ground rise far above the normal voltage magnitude as described above. A grounding transformer placed on the turbine string provides a ground path in the event the string becomes isolated from the system ground.

Construction:

Grounding transformers are normally constructed either with

A ZigZag (Zn) connected winding with or without an auxiliary winding or As a Wye (Ynd) connected winding with a delta connected secondary that may or may not be used to supply auxiliary power

The geometry of the Zig-Zag connection is useful to limit circulation of third harmonics and can be used without a Delta connected winding or the 4- or 5-leg core design normally used for this purpose in distribution and power transformers. Eliminating the need for a secondary winding can make this option both less expensive and smaller than a comparable two-winding grounding transformer. Furthermore, use of a Zig-Zag transformer provides grounding with a smaller unit than a two-winding Wye-Delta transformer providing the same zero sequence impedance.

Wye connected grounding transformers, on the other hand, require either a delta connected secondary or the application of 4 or 5 leg core construction to provide a return flux path for unbalanced loading associated with this primary connection. Since it is often desirable to provide auxiliary power from the grounding transformer secondary winding, this benefit can sway the end user to specify a two-winding grounding transformer in lieu of a Zig-Zag connection. The current trend in wind farm designs is toward the Wye connected primary with a delta secondary.

It is important to understand that both Zig-Zag and two-winding grounding transformers can be provided with the ability to provide auxiliary power, and this can be either a Wye or Delta connected load.

A solidly grounded system using a grounding transformer offers many safety improvements over an ungrounded system. However, the ground transformer alone lacks the current limiting ability of a resistive grounding system. For this reason, neutral ground resistors are often used in conjunction with the grounding transformer to limit neutral ground fault current magnitude. Their ohm values should be specified to allow high enough ground fault current flow to permit reliable operation of the protective relaying equipment, but low enough to limit thermal damage.

How to Specify a Grounding Transformer

The basic parameters required for quoting a grounding transformer are:

Primary Voltage - This is the system voltage to which the grounded winding is to be connected. Don't forget to specify the BIL also. In some cases the BIL will be dictated by equipment considerations, such as 150 kV BIL ratings on 34500 volt wind farms because of the limitation on dead front connectors. Rated KVA - Because the grounding transformer is normally a short time device, its size and cost are less when compared with a continuous duty transformer of equal kVA rating. For this reason, grounding transformers are often not sized by "kVA" but by their continuous and short time current ratings. Regardless of how you rate it, the grounding transformer must be sized to carry the rated continuous primary phase current without exceeding its temperature limit. This load includes the magnetizing current of the core, the capacitive charging current for the cables, and any auxiliary load if applicable. The higher this value, the larger and more costly the transformer will be. Typical continuous current values can be as low as 5 amps to as high as a few hundred. Be sure to include any auxiliary loading requirements. Continuous Neutral Current - The continuous neutral current is defined as three times the phase to current, or in other words, the zero sequence current. This is usually considered to be zero if the system is balanced. However, for the purposes of designing a grounding transformer, it is a value that is expected to flow in the neutral circuit without tripping protective circuits (which would force the current to be zero) or the leakage current to ground that is not a symmetrical function. Again this value is needed to design for thermal capacity of the grounding transformer. Fault current and duration - This value is needed to calculate the short time heating that results from a fault on the system and should be determined from an engineered system study. Typical values for this range from a few hundred amps to a few thousand amps with duration times expressed in seconds and not cycles. For instance, a value of 400 amps for 10 seconds is typical. The fault duration is a critical parameter for the transformer designer. Where protection schemes use the grounding transformer for tripping functions, a relatively short time duration is specified (5 -10 seconds). On the other hand, a continuous or extended neutral fault current duration would be required when the grounding transformer is used in a ground fault alarm scheme. Impedance - The impedance can be expressed as a percentage or as an ohm value per phase. In either case it should be chosen so that the un-faulted phase voltages during a ground fault are within the temporary over-voltage capability of the transformer and associated equipment, such as arresters and terminal connectors. Because of this description, the values can vary from as low as 8% to almost 100%. This value must come from the system designer. Primary winding connection - Specify the type of primary connection, either Zig-Zag or grounded Wye. Secondary connection - specify the secondary voltage and connection when applicable. Specify the size of auxiliary loading to be connected for either Zn or Wye connected primary windings. If the option is to have a two winding transformer with no secondary load, advise if the delta winding can be "buried" (that is not brought out) or if only one bushing is to be brought out for grounding to the tank or testing.

· Basic overall construction features - note the following features as they apply to each transformer
· Compartmental Padmount transformer with integral tamperproof compartment or substation design
· Outdoor or indoor
· Fluid type- mineral oil, silicone, Envirotemp FR3
· Connectivity -dead front, live front, spade terminals, location of terminals - cover or sidewall , exposed or enclosed, etc
· Temperature rise is assumed to be 65'C
· Site elevation or environmental concerns
· Special paint as required
· Neutral Ground Resistors - The rated voltage of the NGR should be equal to the line to ground voltage of the grounding transformer. The current rating and duration should match the grounding transformer ratings. Remember to set the current rating high enough to be above the cable charging current and grounding transformer magnetizing current.


Grounding Transformers - Electrical Design, Transformer Design, and Distribution Transformer Design

Birding Binoculars Ratings Review

Tuesday, March 29, 2011

Transformers the earth - the power of design, planning and design of distribution transformer, transformer

!: Transformers the earth - the power of design, planning and design of distribution transformer, transformer

Grounding is clearly one of the most important aspect of the electrical design, but it continues unabated, misinterpreted and misunderstood. Multi-million dollar loss and liability due to the arc of the earth, so that issues relating to land in the top lists, checking electrical contractor.

Grounding Transformers

In other words, the grounding transformer is used, a dirt road that is a baseless "Y" or delta system. Groundingtransformers are generally used:

Enter a relatively low impedance path to ground, thereby maintaining the system neutral or near ground potential Limit the size of ground faults surge restart Provide a source of fault current during line-to-ground faults Allows the connection of the neutral section you want to load

If a line-to-ground fault occurs on a grounded or isolated, there is no reverseshort-circuit current, so no current flows. The system still works, but the other two fault lines do not enhance tensions in the square root of 3, causing an overload of isolation transformers and other related Components, the system is 173%. MOV arrester is particularly sensitive to heat damage caused by leaking through the blocks, although growth is not enough voltage to flash over. Transformer grounding provides the path to the ground to avoidthis.

Large wind farms provide many examples of the use of the transformer grounded to protect against errors in the lines is not well founded. A lot of wind the transformer is the source of the post only because of the distribution system. When an earth leakage circuit breaker will cause the collector to a cable in the cable channel is open, the wind becomes isolated from the supply chain from source to ground.

The wind does not always detect that error, or a stringisolated and grounded, and the generator to continue to energize the cable collector, and tensions between the non-cable failure, and the rising ground above the normal amount of stress, as described above. Transformer grounding placed on-line turbine provides a dirt road, where the chain is isolated from system ground.

Construction:

grounding transformers are generally built up

Liquidation Z (Zn) with or without relatedauxiliary winding or The Wye (YND) related to the delta winding side, that may or may not be used for auxiliary power

The geometry of the Zig-Zag beneficial relationship by limiting the movement of the third harmonic and can be used without being connected to the winding-up or Delta 4 - or 5-leg base design is usually for the purpose of distribution and power transformers. Eliminating the need for a secondary coil, that this option is cheaper and smaller thansimilar to the two transformer windings to the ground. In addition, the use of Zig-Zag transformer provides the earth with a minor in a two winding transformer is Wye-Delta is the same zero impedance.

Grounded Wye transformer, on the other hand, need or a delta connected secondary or application of the basic 4 or 5 feet building to a flow path back to the unbalanced load with the primary relationship. Since it is often desirableAuxiliary transformer secondary and the earth, this advantage may affect the user enters the transformer is grounded in a relationship instead of two rolls of Zig-Zag. The current trend in the design of the wind farm is connected to the Wye primary and secondary, in the delta.

It is important to understand that two and two Zig-zag grounding transformer winding can be seen that the additional power connector, and it could be either a star or delta connectedthe load.

The transformer is an entrenched system of land offers a number of security enhancements to the system is grounded. However, the soil is not only the transformer capacity limitation of the current system, the grounding resistance. For this reason, the neutral ground resistor is often used in conjunction with limiting the powers of the transformer grounded neutral ground fault current. Ohm value should be that the ground fault current large enough to function reliablyequipment protection relays, but low enough to minimize thermal damage.

Determines how the transformer is grounded

The basic parameters of a transformer, the land must be borne in mind:

Primary voltage - the voltage of the grounding system must be connected to liquidation. Do not forget to add the LIB as well. In some Cases, BIL will be dictated by considerations of equipment, such as the 150-kV BIL ratings windfarms 34500 Sun due to the limitation of deathfirst contact. Rated KVA - Because of the transformer and the ground is a tool, usually of short duration, size and cost is lower than a continuous duty transformer of equal kVA. For this reason, the size of the transformers are often not grounded "but the continuous power handling and a short time during the current assessment. No matter how you rate, the land of the transformer must be sized to carry the rated continuous current without exceeding primary phase in the temperature limit. This awardincludes the core magnetization current, the capacitive charging current of the cables, and any additional charges if applicable. More than this value, the transformer will be larger and more expensive. Typical constant current values ​​can be as low as 5 amps to as high as several hundred. Do not forget to claim any additional loads. Continued neutral current - DC three times the current definition of a neutral phase, or in other words, the sequence of zerocurrent. This is generally considered invalid if the system is in balance. However, the design of a transformer is grounded, it is a value that is expected to flow through the neutral circuit without a protection circuit tripping (which will force the current to zero) or the earth leakage current, which is not a symmetric function. Again, this value is necessary for the design of the heat capacity of the transformer grounded. Short-circuit current duration - This value is requiredcalculate the heating time results in less error in the system and must be determined from a study of the construction system. Typical values ​​from a few hundred amperes to several thousand amperes of seconds, not cycles. For example, typical value of 400 amperes for 10 seconds. The duration of the loss of a critical parameter for the design of the transformer. When the protection systems of the earth to the transformer tripping functionality in a relatively short period of timespecified duration (5 -10 seconds). On the other hand, because of the continuous or sustained period of neutral current would be needed if the transformer is used to earth ground fault alarm. Impedance - The impedance can be expressed as a percentage value, or ohms per phase. In both Cases must be chosen so that the phase voltages do not blame him when the earth is temporary capacity-voltage equipment and associated processing, such asarrester and the terminal connectors. Since this description, the range of values, only 8% to almost 100%. This value must come from the system designer. Primary connection - Specify the type of primary contact or zig-zag grounded Wye. Secondary connection - Specify the secondary voltage and a good connection. Specify the size of the additional load must be connected to either Zn-or Wye connected primary windings. If the possibility that twotransformer secondary winding is vacuum condition in the delta winding can be "buried" (not shown), or a jack to raise the ground or the shell of the investigation.

· Services basic general construction - note the following features that apply to each processor
· Transformer built-in tamper-proof compartment stand compartmentalized design position
· Outdoors or inside
° Fluid type of mineral oil,Silicone Envirotemp FR3
· Connectivity pre-outs, live clips, location of terminals - and covers the flanks, exposed, or closed, etc.
• Temperature growth is assumed to 65'C
Site · rise, or environmental concerns
Painting requires special ·
· Resistance neutral ground - the nominal voltage of the NGR should be equal to the line and the earth grounding transformer. The current rating and the duration should becorrespond to the dimensions of the transformer grounded. Do not forget the current rating high enough to exceed the charging cable and a grounding transformer magnetizing current.


Transformers the earth - the power of design, planning and design of distribution transformer, transformer

!: Teva Mens Hurricane 3 Outdoor Sandal by Teva !: Trackball Keyboard Wireless !: Buying Generator Pto Driven


Twitter Facebook Flickr RSS



Français Deutsch Italiano Português
Español 日本語 한국의 中国简体。